/build/static/layout/Breadcrumb_cap_w.png

Overlooking something for enablebitlocker.vbs deployment??

I am attempting to deploy enablebitlocker.vbs to existing and new system as part of a company upgrade project. I have used the CCTK to create a package to change bios settings as the first post install task including turning on the TPM setting. I have also pushed this from the K1000 to test and it works great. The second post task is the enablebitlocker.vbs script to start the encryption. I have searched the internet to make sure that I am doing this correctly and found that my post config setup is identical to those that have deployed this in the past..

Dependencies:Enablebitlocker.vbs

Task1

On Success:

Launch Program

Directory: $(KACE_SYS_DIR)

File: cscript.exe

Parameters: $(KACE_DEPENDENCY_DIR)\enablebitlocker.vbs /on:tpm /l:c:\bitlockertemp\bitlocker.txt

Here is where this becomes very odd.. The task completes successfully on both the K1000 and the k2000 but nothing happens.. I have made sure the TPM is enabled and ready.. I have run this as Local and as Network Admin.. I assume because it does not fail there is no log created because it is not created. I have tested the script to make sure it is not an issue with the VBS and it works fine..

I have just tried to run this as a .BAT file:

cscript enablebitlocker.vbs /on:tpm /l:c:\bitlockertemp\bitlocker.txt

Again it shows completed successfully but nothing on the client side. I can also run this script local and it works fine.

I am deploying this to new Dell E7240 machines with Windows Enterprise x64 operating systems..

Any help would be greatly appreciated.. At this point I would even be happy with another way to complete the task as long as it works.. LOL

Thank you in advance!!



0 Comments   [ + ] Show comments

Answers (2)

Posted by: SMal.tmcc 9 years ago
Red Belt
1
try calling it this way.  Make sure you use the double quotes.



Comments:
  • Thank you for your response SMal.

    I have attempted to call the script as shown and I am still getting the same.. The script shows it has completed but nothing happens.. After further testing I have found that I can run the script on my personal machine ( I am local admin ) but am unable to run the script on the target machines at all.. It would seem that it does not like network admin creds to run the script.. I would assume that you would need to run as local admin but have been unable to do this on the new machines - tmcvay828 9 years ago
    • If the network credentials are members of the local admin group it should make no difference.

      Can you share your vbs script. The problem could be that the kace client is 32bit so it would redirect any calls to the 32 bit syswow64 directory. If you are making exe calls within your script trying using the full path for the exe vs just the exe's name. See new answer for some links of past bitlocker problems this helped on. - SMal.tmcc 9 years ago
      • Hello SMal.. I am using the un edited enablebitlocker.vbs Sample Deployment Script unedited at this point.. Here is the script

        '===============================================================================
        '
        ' This sample script can be used to automate the deployment of BitLocker using the BitLocker WMI interfaces.
        '
        ' Last Updated: 7/1/2006
        ' Last Reviewed: 9/9/2009
        ' Microsoft Corporation
        '
        ' Disclaimer
        '
        ' The sample scripts are not supported under any Microsoft standard support program or service. The sample scripts are provided AS IS without warranty of any kind.
        ' Microsoft further disclaims all implied warranties including, without limitation, any implied warranties of merchantability or of fitness for a particular purpose.
        ' The entire risk arising out of the use or performance of the sample scripts and documentation remains with you. In no event shall Microsoft, its authors, or anyone else involved in the creation, production, or delivery of the scripts be liable for any damages whatsoever (including, without limitation, damages for loss of business profits, business interruption, loss of business information, or other pecuniary loss) arising out of the use of or inability to use the sample scripts or documentation, even if Microsoft has been advised of the possibility of such damages.
        '
        'Version 1.2 - Updates
        '1 - Removed infinate loop potential in the FindRemoveableDrive function. Three attempts are valid.
        '2 - Added saving RK to the /USB option.
        '3 - Will not look at local evet log if no policy key present.
        '4 - Minor loging and text changes.
        '5 - Fixed PIN input cancel button use.
        '
        'Version 1.2.1 - Tested and re-released for Windows 7 and Windows Server 2008 R2
        '
        '===============================================================================================================
        'Script arguments
        '/on:<tpm,tp,tsk,usb> used to specify options for turning on BitLocker (tpm,tp,tsk) REQUIRED
        '/l:<location> specify to create a log file and it's location REQUIRED
        '/em:<128d,256d,128,256> used to specify encryption algorithm (aes128d, aes256d, aes128, aes256) OPTIONAL
        '/rk create a recovery key and store in a particular location OPTIONAL
        '/promptuser causes script to prompt user for TPM PIN or to insert USB drive OPTIONAL
        '/sms creates an SMS status MIF for software distribution OPTIONAL
        '/ro:"<existingTPMownerpassword>" changes the TPM ownership password (password must be placed between "") OPTIONAL
        '----------------------------------------------------------------------------------------
        'Constants And Variables
        '----------------------------------------------------------------------------------------
        On Error Resume Next

        Const ForAppending = 8
        Const SetPres = 10
        const HKEY_LOCAL_MACHINE = &H80000002
        const REG_SZ = 1
        const REG_EXPAND_SZ = 2
        const REG_BINARY = 3
        const REG_DWORD = 4
        const REG_MULTI_SZ = 7

        Dim bIsEnabled,bIsActivated,bIsOwned,bIsOwnershipAllowed,objTPM,objLog,TakeOwnership,Enable,objEnVol,strStatusTPM,strStatusBDE,strStatusTPMState
        Dim objGPPT,strOwnerPassword,strPassword,objWMIBDE,nProtStatus,ProtectVar,objOSSysDriv,objSWbemServices,objOS,coloperatingsystem,sProtID,strOldOwnerPassword
        Dim argProtect,argRK,argEM,argSMS,argLOG,argRO,argPrompt,strCurrentUser,argValid,i,strPIN,objRemovableDrive,strStatusCode,strStatusData,MIF,strEKP,strEK
        Dim ActiveDirectoryBackup,ActiveDirectoryInfoToStore,RequireActiveDirectoryBackup,EncryptionMethod,BackupMandatory,strStartDate,strStartTime,strRetry,strPolicy

        '----------------------------------------------------------------------------------------
        'General 1 - Get ready to run, create objects, create log file, parse command line arguments
        '----------------------------------------------------------------------------------------
        Set objFSO = CreateObject("Scripting.FileSystemObject")
        Set WSHShell = WScript.CreateObject("WScript.Shell")

        'Parse command line arguments
        Set args = WScript.Arguments
        Argument1 = args.Item(0)
        Argument2 = args.Item(1)
        NumberofArgs = WScript.Arguments.Count
        Set colNamedArgs = WScript.Arguments.Named

        'Get all command line arguments and set them to lower Case
        argProtect = LCase(colNamedArgs.Item("on"))
        argRK = LCase(colNamedArgs.Item("rk"))
        argEM = LCase(colNamedArgs.Item("em"))
        argLOG = LCase(colNamedArgs.Item("l"))
        argPrompt = LCase(colNamedArgs.Item("promptuser"))
        argSMS = LCase(colNamedArgs.Item("sms"))
        strOldOwnerPassword = LCase(colNamedArgs.Item("ro"))

        'Evaluate named optional arguments
        If colNamedArgs.Exists("rk") Then
        argRK = "1"
        Else
        argRK = "No recovery key use specified"
        End If
        If colNamedArgs.Exists("sms") Then
        argSMS = "1"
        Else
        argSMS = "No SMS status MIF's will be created"
        End If
        If colNamedArgs.Exists("ro") Then
        argRO = "1"
        Else
        argRO = "TPM ownership information will not be cleared"
        End If
        If colNamedArgs.Exists("promptuser") Then
        argPrompt = "1"
        Else
        argPrompt = "Users will not be prompted for PIN or to insert USB key"
        End If

        'Evaluate emcyption method if on command line
        If Not colNamedArgs.Exists("em") Then
        argEM = "1"
        Else If argEM = "" Then
        argEM = "1"
        Else If argEM = "128d" Then
        argEM = "1"
        Else If argEM = "256d" Then
        argEM = "2"
        Else If argEM = "128" Then
        argEM = "3"
        Else If argEM = "256" Then
        argEM = "4"
        End If
        End If
        End If
        End If
        End If
        End If

        'Create log file
        Set objLog = objFSO.OpenTextFile(argLOG,ForAppending,True)
        objlog.writeline "Script processing started " & Date & " " & Time
        strStartDate = Date
        strStartTime = Time

        'Set the SMS default status exit code
        strStatusCode = 1

        'Check arguments for requiered options
        If Not colNamedArgs.Exists("on") Then
        strStatusData = "No /on option was specified on the command line."
        objLog.Writeline strStatusData
        Wscript.Echo strStatusData
        strStatusCode = 0
        CreateStatusMIF strStatusData
        ShowHelp

        Else If Not colNamedArgs.Exists("l") Then
        strStatusData = "No /l option specified on the command line."
        objLog.Writeline strStatusData
        Wscript.Echo strStatusData
        strStatusCode = 1
        CreateStatusMIF strStatusData
        ShowHelp
        Else If NumberofArgs < 2 Then
        strStatusData = "The required number of arguments of 2 was not met."
        objLog.Writeline strStatusData
        Wscript.Echo strStatusData
        strStatusCode = 1
        CreateStatusMIF strStatusData
        ShowHelp
        Else If ((argProtect = "tp") Or (argProtect = "tsk")) And argPrompt <> "1" Then
        strStatusData = "Using the options /on:tp or /on:tsk and not using /promptuser is not allowed."
        objLog.Writeline strStatusData
        Wscript.Echo strStatusData
        strStatusCode = 1
        CreateStatusMIF strStatusData
        ShowHelp
        Else If argProtect = "usb" And argPrompt <> "1" Then
        strStatusData = "Using the options /on:usb and not using /promptuser is not allowed."
        objLog.Writeline strStatusData
        Wscript.Echo strStatusData
        strStatusCode = 1
        CreateStatusMIF strStatusData
        ShowHelp
        Else If argRK = "1" And argPrompt <> "1" Then
        objLog.Writeline "Using the option /rk and not using /promptuser is not allowed."
        Wscript.Echo "Using the option /rk and not using /promptuser is not allowed."
        ShowHelp
        Else
        If argProtect = "tp" Or argProtect = "tpm" Or argProtect = "tsk" Or argProtect = "usb" Then
        objLog.Writeline "Proper number of command line arguments passed to the script"
        Else
        objLog.Writeline "The /on option does not match one of the required options."
        Wscript.Echo "The /on option does not match one of the required options."
        ShowHelp
        End If
        End If
        End If
        End If
        End If
        End If
        End If

        'Output command arguments to log file
        objLog.Writeline "-----------------------------------------------------------------------"
        objLog.Writeline "---------------Executing with the following arguments------------------"
        objLog.Writeline "-----------------------------------------------------------------------"
        objLog.Writeline "Enable parameters: " & argProtect
        objLog.Writeline "Logging location: " & argLOG
        objLog.Writeline "Create recovery key: " & argRK
        objLog.Writeline "Encryption method: " & argEM
        objLog.Writeline "Create SMS status MIF's: " & argSMS
        objLog.Writeline "Reset TPM ownership: " & argRO
        objLog.Writeline "User prompting: " & argPrompt
        objLog.Writeline "-----------------------------------------------------------------------"

        '----------------------------------------------------------------------------------------
        'General 2 - Main script processing area
        '----------------------------------------------------------------------------------------

        ConnectTPMProv() 'Connect to the TPM WMI provider

        If argProtect = "usb" Then
        ConnectBDEProv() 'Connect to the volume encryption WMI provider
        EvalGPO()
        GetBDEStatus()
        Else
        GetTPMStatus() 'Get the current status of the TPM to determine action
        ConnectBDEProv() 'Connect to the volume encryption WMI provider

        'The following If statements cause the script to react differently depending on the TPM state

        If bIsEnabled = "True" and bIsActivated = "True" and bIsOwned = "True" Then
        objlog.writeline "TPM is in a ready state to enable BitLocker."
        If argRO = "1" Then
        objlog.writeline "Change TPM owner password specified on the command line."
        DenTPMPassword
        ChangeOwnerAuth strOldOwnerPassword,strOwnerPassword
        EvalGPO()
        GetBDEStatus()
        Else
        EvalGPO()
        GetBDEStatus()
        End If
        Else If bIsEnabled = "True" and bIsActivated = "True" and bIsOwned = "False" Then
        objlog.writeline "TPM ownership is not taken...will take ownership."
        DenTPMPassword
        OwnTPM
        EvalGPO()
        GetBDEStatus()
        Else If bIsEnabled = "False" And bIsActivated = "False" and bIsOwned = "False" Then
        objlog.writeline "TPM is not turned on...will Enable and Activate TPM and force a reboot."
        EnableActivateTPM()
        Else If bIsEnabled = "False" and bIsActivated = "False" and bIsOwned = "True" Then
        objlog.writeline "TPM is not turned on...will Enable and Activate TPM and force a reboot."
        EnableActivateTPM()
        Else If bIsEnabled = "True" and bIsActivated = "False" and bIsOwned = "False" Then
        objlog.writeline "TPM is turned but not activated...will Activate TPM and force a reboot."
        EnableActivateTPM()
        End If
        End If
        End If
        End If
        End If
        End If

        If strStatusCode = 1 then
        strStatusData = strStatusTPMState & ". " & strStatusTPM & " " & "The volume has a protection status of: " & nProtStatus & ". " & strStatusBDE & ". " & "Script Completed Successfully"
        objLog.writeline strstatusdata
        CreateStatusMIF strStatusData
        End if
        objlog.writeline "Script ended " & Date & " " & Time

        '----------------------------------------------------------------------------------------
        'Functions and subs
        '----------------------------------------------------------------------------------------
        'Function 1 - Connect to TPM WMI provider
        '----------------------------------------------------------------------------------------

        Function ConnectTPMProv()
        strConnectionStr1 = "winmgmts:{impersonationLevel=impersonate,authenticationLevel=pktPrivacy}!root\cimv2\Security\MicrosoftTpm"

        err.clear
        Set objWMITPM = GetObject(strConnectionStr1)
        If Err.Number <> 0 Then
        strStatusData = "ERROR - Failed to connect to the MicrosoftTPM provider. Script is exiting..."
        objLog.Writeline strStatusData
        strStatusCode = 0
        CreateStatusMIF strStatusData
        Wscript.Quit -1
        Else
        objLog.Writeline "Connection succeeded to MicrosoftTPM"
        End If
        err.clear

        ' There should either be 0 or 1 instance of the TPM provider class
        Set colTpm = objWMITPM.InstancesOf("Win32_Tpm")

        If colTpm.Count = 1 And argProtect = "usb" Then
        strStatusData = "Successfully retieved a TPM from the provider class. USB only protection was chosen and cannot be used when a TPM is present. Script is exiting...(Error: " & Err.Number & ")"
        objLog.Writeline strStatusData
        strStatusCode = 0
        CreateStatusMIF strStatusData
        WScript.Quit -1
        Else If colTpm.Count = 0 And argProtect = "usb" Then
        objLog.Writeline "Protect option is set for USB only. Will continue with USB only protection..."
        Exit Function
        Else If colTpm.Count = 0 And argProtect <> "usb" Then
        strStatusData = "ERROR - Failed get a TPM instance in the provider class. Script is exiting..."
        objLog.Writeline strStatusData
        strStatusCode = 0
        CreateStatusMIF strStatusData
        WScript.Quit -1
        End If
        End If
        End If
        Err.Clear

        'Get a single instance of the TPM provider class
        Set objTpm = objWMITPM.Get("Win32_Tpm=@")
        If Err.Number <> 0 Then
        strStatusData = "ERROR - Failed get a TPM instance in the provider class. Script is exiting...(Error: " & Err.Number & ")"
        objLog.Writeline strStatusData
        strStatusCode = 0
        CreateStatusMIF strStatusData
        WScript.Quit -1
        Else
        objLog.Writeline "Successfully retrieved a TPM instance from the Win32_TPM provider class"
        End If
        Err.Clear

        End Function

        '----------------------------------------------------------------------------------------
        'Function 2 - Connect to BDE WMI provider
        '----------------------------------------------------------------------------------------

        Function ConnectBDEProv()

        strConnectionStr2 = "winmgmts:{impersonationLevel=impersonate,authenticationLevel=pktPrivacy}!root\cimv2\Security\MicrosoftVolumeEncryption"

        err.clear
        Set objWMIBDE = GetObject(strConnectionStr2)
        If Err.Number <> 0 Then
        strStatusData = "ERROR - Failed to connect to the MicrosoftVolumeEncryption provider. Script is exiting...(Error " & Err.Number & ")"
        objLog.Writeline strStatusData
        strStatusCode = 0
        CreateStatusMIF strStatusData
        WScript.Quit -1
        Else
        objLog.Writeline "Connection succeeded to MicrosoftVolumeEncryption"
        End If
        err.clear

        End Function

        '-----------------------------------------------------------------------------------------
        'Function 3 - Get BDE status data and enable encryption
        '-----------------------------------------------------------------------------------------

        Function GetBDEStatus()

        Set colEnVol = objWMIBDE.ExecQuery("Select * from Win32_EncryptableVolume")
        objlog.writeline "EncryptableVolumes count is: " & colEnVol.count

        If colEnVol.count < 1 then
        strStatusData = "ERROR - EncryptableVolumes is null and count is: " & colEnVol.count & " Script is quitting..."
        objLog.Writeline strStatusData
        strStatusCode = 0
        CreateStatusMIF strStatusData
        WScript.Quit -1
        Else
        strConnectionStr3 = "winmgmts:{impersonationLevel=impersonate,authenticationLevel=pktPrivacy}!root\cimv2"
        Set objSWbemServices = GetObject(strConnectionStr3)
        Set coloperatingsystem = objSWbemServices.ExecQuery("Select * from Win32_OperatingSystem")
        For each objOperatingSystem in colOperatingSystem
        strWin32SysDrive = objOperatingSystem.SystemDrive
        Next

        For Each objEnVol in colEnVol
        objlog.writeline "The EncryptableVolume(s) found: " & objEnVol.DeviceID
        strEncDriveLetter = objEnVol.DriveLetter

        If strEncDriveLetter = strWin32SysDrive then
        objlog.writeline "EncryptableVolume used for encryption is: " & strEncDriveLetter
        intRC = objEnVol.GetProtectionStatus(nProtStatus)
        objlog.writeline "The volume has a protection status of: " & nProtStatus

        If nProtStatus = 1 then
        strStatusData = "BitLocker Protection is already enabled. Check log file for more details. Process is quitting..."
        objLog.Writeline strStatusData
        strStatusCode = 0
        CreateStatusMIF strStatusData
        Wscript.quit -1
        Else
        If nProtStatus = 0 then
        objlog.writeline "BitLocker Protection is Off"
        nRC = objEnVol.GetConversionStatus(strCS)
        objlog.writeline "Get conversion status is: " & strCS
        If strCS = 0 Then
        err.Clear
        objlog.writeline "The volume has a status of fully decrypted"

        If argProtect = "tpm" Then
        intRC = objEnVol.ProtectKeyWithTPM("TPM Protection",Empty,sProtID)
        objLog.Writeline "Attempting to enable BitLocker TPM"
        If intRC <> 0 Then
        CheckError intRC
        strStatusData = "ERROR - the ProtectKeyWithTPM Method failed with the exit code: " & Hex(intRC)
        objLog.Writeline strStatusData
        strStatusCode = 0
        CreateStatusMIF strStatusData
        Else
        strStatusData = "Successfully initiated ProtectKeyWithTPM Method with an exit code of: " & Hex(intRC)
        objlog.writeline strStatusData
        strStatusBDE = strStatusData
        CheckUser
        CreateRP objEnVol
        EnableBitlocker objEnVol
        CreateRK sProtID
        End If
        err.clear

        Else
        If argProtect = "tp" Then
        CheckUser
        GetPIN
        If argPrompt = "1" and strCurrentUser = "1" and argValid = "1" Then
        intRC = objEnVol.ProtectKeyWithTPMAndPIN("TPM and PIN Protection",Empty,strPIN,sProtID)
        objLog.Writeline "Attempting to enable BitLocker TPM + Pin"
        If intRC <> 0 Then
        CheckError intRC
        strStatusData = "ERROR - the ProtectKeyWithTPMAndPIN Method failed with the exit code: " & Hex(intRC)
        objLog.Writeline strStatusData
        strStatusCode = 0
        CreateStatusMIF strStatusData
        Else
        strStatusData = "Successfully initiated ProtectKeyWithTPMAndPIN Method with an exit code of: " & Hex(intRC)
        objlog.writeline strStatusData
        strStatusBDE = strStatusData
        CreateRP objEnVol
        EnableBitlocker objEnVol
        CreateRK sProtID
        End If
        err.clear
        Else
        strStatusData = "ERROR - TPM and PIN Protection failed. One of the following conditions was not met: Command line switch /promptuser not used, No logged on User, or PIN was not of a valid format"
        objlog.writeline strStatusData
        strStatusBDE = strStatusData
        Exit Function
        End If
        Else
        If argProtect = "tsk" Then
        CheckUser
        If argPrompt = "1" Then
        FindRemovableDrive()
        Else
        objLog.WriteLine "TPM and StarupKey option is chosen and user prompting for USB device is disabled. Script is exiting..."
        FindRemovableDrive()
        Exit Function
        End If
        intRC = objEnVol.ProtectKeyWithTPMAndStartupKey("TPM and Startup Key Protection",Empty,Empty,sProtID)
        objLog.Writeline "Attempting to enable BitLocker TPM + StartupKey"
        If intRC <> 0 Then
        CheckError intRC
        strStatusData = "ERROR - the ProtectKeyWithTPMAndStartupKey Method failed with the exit code: " & Hex(intRC)
        objLog.Writeline strStatusData
        strStatusCode = 0
        CreateStatusMIF strStatusData
        Else
        objlog.writeline "Successfully initiated ProtectKeyWithTPMAndStartupKey Method with an exit code of: " & Hex(intRC)
        objLog.Writeline "Attempting to save startup key..."
        intRC = objEnVol.SaveExternalKeyToFile(sProtID,objRemovableDrive)
        If intRC <> 0 Then
        strStatusData = "ERROR - Failed to save the startup key to a USB drive with the following exit code: " & Hex(intRC)
        objLog.Writeline strStatusData
        strStatusCode = 0
        CreateStatusMIF strStatusData
        Else
        strStatusData = "Successfully completed ProtectKeyWithTPMAndStartupKey Method and saved the startup key to USB drive with an exit code of: " & Hex(intRC)
        objlog.writeline strStatusData
        strStatusBDE = strStatusData
        CreateRP objEnVol
        EnableBitlocker objEnVol
        CreateRK sProtID
        End If
        err.clear
        End If
        err.clear
        Else
        If argProtect = "usb" then
        CheckUser
        FindRemovableDrive()
        intRC = objEnVol.ProtectKeyWithExternalKey("USB Key Protection",Empty,sProtID)
        objLog.Writeline "Attempting to enable BitLocker with External Key only"
        If intRC <> 0 Then
        CheckError intRC
        strStatusData = "ERROR - the ProtectKeyWithExternalKey Method failed with the exit code: " & Hex(intRC)
        objLog.Writeline strStatusData
        strStatusCode = 0
        CreateStatusMIF strStatusData
        Else
        objlog.writeline "Successfully initiated ProtectKeyWithExternalKey Method with an exit code of: " & Hex(intRC)
        objLog.Writeline "Attempting to save USB key..."
        intRC = objEnVol.SaveExternalKeyToFile(sProtID,objRemovableDrive)
        If intRC <> 0 Then
        strStatusData = "ERROR - Failed to save the startup key to a USB drive with the following exit code: " & Hex(intRC)
        objLog.Writeline strStatusData
        strStatusCode = 0
        CreateStatusMIF strStatusData
        Else
        strStatusData = "Successfully completed ProtectKeyWithExternalKey Method and saved the startup key to USB drive with an exit code of: " & Hex(intRC)
        objlog.writeline strStatusData
        strStatusBDE = strStatusData
        CreateRP objEnVol
        EnableBitlocker objEnVol
        CreateRK sProtID
        End If
        err.clear
        End If
        End If
        End If
        End If
        End If
        End if
        End if
        End if
        End if

        Next
        If strCS = "" Then
        strStatusData = "ERROR - The available encyptable volumes must match the operating system volume and this did not occur. Operating system drive found - " & strWin32SysDrive
        objLog.Writeline strStatusData
        strStatusCode = 0
        CreateStatusMIF strStatusData
        Else
        GetConversionStatus strCS
        End If
        End If
        End Function

        '-----------------------------------------------------------------------------------------
        'Function 4 - Get TPM status data to determine if TPM is enabled, activated, and owned
        '-----------------------------------------------------------------------------------------

        Function GetTPMStatus()

        nRC = objTpm.IsEnabled(bIsEnabled)
        If nRC <> 0 Then
        strStatusData = "ERROR - The method IsEnabled failed with return code 0x" & Hex(nRC)
        objLog.Writeline strStatusData
        strStatusCode = 0
        CreateStatusMIF strStatusData
        End If

        nRC = objTpm.IsActivated(bIsActivated)
        If nRC <> 0 Then
        strStatusData = "ERROR - The method IsActivated failed with return code 0x" & Hex(nRC)
        objLog.Writeline strStatusData
        strStatusCode = 0
        CreateStatusMIF strStatusData
        End If

        nRC = objTpm.IsOwned(bIsOwned)
        If nRC <> 0 Then
        strStatusData = "ERROR - The method IsOwned failed with return code 0x" & Hex(nRC)
        objLog.Writeline strStatusData
        strStatusCode = 0
        CreateStatusMIF strStatusData
        End If

        'Output TPM status information to the log file
        objLog.WriteLine "TPM found in the following state:"
        objLog.WriteLine "Enabled - " & bIsEnabled
        objLog.WriteLine "Activated - " & bIsActivated
        objLog.WriteLine "Owned - " & bIsOwned

        strStatusTPMState = "TPM found in the following state: Enabled - " & bIsEnabled & ", Activated - " & bIsActivated & ", Owned - " & bIsOwned

        End Function

        '-----------------------------------------------------------------------------------------
        'Function 5 - Enable and Activate TPM
        '-----------------------------------------------------------------------------------------

        Function EnableActivateTPM

        Err.clear

        'Enable and activate TPM device

        intRC = objTPM.SetPhysicalPresenceRequest(SetPres)
        objLog.Writeline "Attempting to enable and activate the TPM"
        If intRC <> 0 Then
        strStatusData = "ERROR - failed to enable and activate the TPM with the following exit code: " & Hex(intRC)
        objLog.Writeline strStatusData
        strStatusCode = 0
        CreateStatusMIF strStatusData
        Else
        objlog.writeline "Completed enabling and activating the TPM with an exit code of: " & Hex(intRC)
        End If

        intRC = objTPM.GetPhysicalPresenceTransition(strPT)
        objlog.writeline "Presence Transition = " & strPT
        If intRC <> 0 Then
        strStatusData = "ERROR - failed to get PhysicalPresenceTransition with the following exit code: " & Hex(intRC)
        objLog.Writeline strStatusData
        strStatusCode = 0
        CreateStatusMIF strStatusData
        Else
        objlog.writeline "Completed PhysicalPresenceTransition with an exit code of: " & Hex(intRC)
        End If

        If strPT = 0 then
        objlog.writeline "The platform does not need to transition"
        Else
        If strPT = 1 then
        strStatusData = "Shutting down system to finish enabling the TPM"
        objlog.writeline strStatusData
        strStatusTPM = strStatusData
        oReboot = WSHShell.Run("shutdown.exe /s /t 5",2,True)
        '***** Add status code???
        Else
        If strPT = 2 then
        objlog.writeline "Rebooting system to finish enabling the TPM"
        oReboot = WSHShell.Run("shutdown.exe /r /t 5",2,True)
        '***** Add status code???
        Else
        If strPT = 3 Then
        strStatusData = "The TPM transition is vendor-specific cannot continue. Contact your vendor for instructions. Script is quitting..."
        objLog.Writeline strStatusData
        strStatusCode = 0
        CreateStatusMIF strStatusData
        WScript.Quit -1
        End if
        End if
        End if
        End if

        End Function

        '-----------------------------------------------------------------------------------------
        'Function 6 - Create a recovery key if specified on command line
        '-----------------------------------------------------------------------------------------
        Function CreateRK(sProtID)
        If argRK = "1" Then
        FindRemovableDrive()
        intRC = objEnVol.ProtectKeyWithExternalKey("Recovery Protection",Empty,sProtID)
        objLog.Writeline "Attempting to create BitLocker Recovery Key."
        If intRC <> 0 Then
        objlog.writeline "ERROR - Failed generating Recovery Key with the exit code: " & Hex(intRC)
        Else
        objlog.writeline "Successfully generated Recovery key with an exit code of: " & Hex(intRC)
        objLog.Writeline "Attempting to save Recovery Key to USB..."
        intRC = objEnVol.SaveExternalKeyToFile(sProtID,objRemovableDrive)
        If intRC <> 0 Then
        objlog.writeline "ERROR - Failed to save the recovery key to a USB drive with the following exit code: " & Hex(intRC)
        Else
        objlog.writeline "Successfully saved the recovery key to USB drive with an exit code of: " & Hex(intRC)
        End If
        err.clear
        End If
        End If

        End Function

        '-----------------------------------------------------------------------------------------
        'Function 7 - Changing TPM owner information
        '-----------------------------------------------------------------------------------------
        Function ChangeOwnerAuth(strOldOwnerPassword,strOwnerPassword)
        err.clear

        ' Convert the owner password to owner authorization by using SHA-1 hashing
        intRC = objTpm.ConvertToOwnerAuth(strOldOwnerPassword, OldOwnerAuthDigest)
        If intRC <> 0 Then
        objlog.writeline "ERROR - Failed to converting old owner password to owner authorization: " & Hex(intRC)
        Else
        objlog.writeline "Completed converting old owner password to owner authorization: " & Hex(intRC)
        End If
        err.clear

        intRC = objTpm.ConvertToOwnerAuth(strOwnerPassword, OwnerAuthDigest)
        If intRC <> 0 Then
        objlog.writeline "ERROR - Failed to converting owner password to owner authorization: " & Hex(intRC)
        Else
        objlog.writeline "Completed converting owner password to owner authorization: " & Hex(intRC)
        End If
        err.clear

        ' Change owner authorization on the TPM
        intRC = objTpm.ChangeOwnerAuth(OldOwnerAuthDigest,OwnerAuthDigest)
        objlog.writeline "Starting to change owner authorization process on the TPM"
        If intRC <> 0 Then
        objlog.writeline "ERROR - Failed to change owner authorization on the TPM with the following exit code: " & Hex(intRC)
        Else
        objlog.writeline "Completed change owner authorization process on the TPM with the following exit code: " & Hex(intRC)
        End If
        err.clear

        'Wait for TPM to finish ownership process
        Wscript.Sleep(10000)

        End Function

        '-----------------------------------------------------------------------------------------
        'Function 8 - Generate random string for TPM owner password. This password will range
        'from 7-14 characters and will contain numbers and letters.
        '-----------------------------------------------------------------------------------------
        Function DenTPMPassword

        'Upper and lower limits for TPM owner password
        intUpperLimit = 14
        intLowerLimit = 7

        Randomize
        intCharacters = Int(((intUpperLimit - intLowerLimit + 1) * Rnd) + intUpperLimit)

        intUpperLimit = 126
        intLowerLimit = 33

        For i = 1 to intCharacters
        Randomize
        intASCIIValue = Int(((intUpperLimit - intLowerLimit + 1) * Rnd) + intLowerLimit)
        strPassword = strPassword & Chr(intASCIIValue)
        Next

        strOwnerPassword = strPassword
        objLog.WriteLine "Random TPM owner password is: " & strOwnerPassword

        End Function

        '-----------------------------------------------------------------------------------------
        ' Function 9 - Check for endoresement key and take ownership of TPM
        '-----------------------------------------------------------------------------------------

        Function OwnTPM

        err.clear

        'Check for the presence of Endorsement Key Pair and create one if not found
        intRC = objTpm.IsEndorsementKeyPairPresent(strEK)
        If intRC <> 0 Then
        strStatusData = "ERROR - Failed to determine if Endorsement Key Pair is present with the following exit code: " & Hex(intRC)
        objLog.Writeline strStatusData
        strStatusCode = 0
        CreateStatusMIF strStatusData
        Else
        objlog.writeline "Successfully determined if Endorsement Key Pair is present with an exit code of: " & Hex(intRC)
        objlog.writeline "IsEndorsementKeyPairPresent returned a value of: " & strEK
        End If
        err.clear

        If strEK = "True" then
        objlog.writeline "Endorsement Key Pair is present."
        Else
        objlog.writeline "Attempting to create Endorsement Key Pair"
        intRC = objTpm.CreateEndorsementKeyPair(strEKP)
        If intRC <> 0 Then
        strStatusData = "ERROR - Failed to create Endorsement Key Pair with the following exit code: " & Hex(intRC)
        objLog.Writeline strStatusData
        strStatusCode = 0
        CreateStatusMIF strStatusData
        Wscript.quit -1
        Else
        objlog.writeline "Successfully created Endorsement Key Pair with an exit code of: " & Hex(intRC)
        End If
        End if

        err.clear

        ' Convert the owner password to owner authorization by using SHA-1 hashing
        intRC = objTpm.ConvertToOwnerAuth(strOwnerPassword, OwnerAuthDigest)
        If intRC <> 0 Then
        strStatusData = "ERROR - Failed to hash TPM owner password with the following exit code: " & Hex(intRC)
        objLog.Writeline strStatusData
        strStatusCode = 0
        CreateStatusMIF strStatusData
        Wscript.quit -1
        Else
        objlog.writeline "Successfully hashed TPM owner password with an exit code of: " & Hex(intRC)
        End If

        ' Take ownership of the TPM - two string values to be hashed using SHA-1
        intRC = objTpm.TakeOwnership(OwnerAuthDigest)
        objlog.writeline "Starting to take ownership of the TPM"
        If intRC <> 0 Then
        strStatusData = "ERROR - Failed to take ownership of the TPM with the following exit code: " & Hex(intRC)
        objLog.Writeline strStatusData
        strStatusCode = 0
        CreateStatusMIF strStatusData
        Else
        objlog.writeline "Completed taking ownership of the TPM with an exit code of: " & Hex(intRC)
        End If
        err.clear

        'Wait for TPM to finish ownership process
        Wscript.Sleep(10000)

        End Function

        '-----------------------------------------------------------------------------------------
        'Function 10 - Enable Bitlocker
        '-----------------------------------------------------------------------------------------

        Function EnableBitlocker(objEnVol)

        Err.clear
        intRC = objEnVol.Encrypt(argEM)
        objLog.Writeline "Attempting to enable BitLocker..."
        If intRC <> 0 Then
        strStatusData = "ERROR - failed to initiate drive encryption with the following exit code: " & Hex(intRC)
        objLog.Writeline strStatusData
        strStatusCode = 0
        CreateStatusMIF strStatusData

        objLog.Writeline "Deleting previously created key protectors..."
        intRC = objEnVol.DeleteKeyProtectors()
        If intRC <> 0 Then
        strStatusData = "ERROR - failed to remove key protectors with the following exit code: " & Hex(intRC) & " Script is quitting..."
        objLog.Writeline strStatusData
        Else
        objlog.writeline "Successfully removed key protectors with the following exit code: " & Hex(intRC) & " Script is quitting..."
        End If

        Else
        objlog.writeline "Successfully initiated BitLocker drive encryption with an exit code of: " & Hex(intRC)
        End If
        err.clear

        End Function

        '--------------------------------------------------------------
        'Function 11 - Find the removeable drive in WMI
        '--------------------------------------------------------------
        Function FindRemovableDrive()

        strRetry = strRetry + 1
        If strRetry > 3 Then
        strStatusData = "ERROR - User did not input a valid USB device within the 3 attempts allowed. Script is quitting..."
        objLog.Writeline strStatusData
        strStatusCode = 0
        CreateStatusMIF strStatusData
        Wscript.Quit -1
        End If

        Err.Clear
        Set colDrives = objSWbemServices.ExecQuery("Select * from Win32_Volume where DriveType = '2'")
        If Err.Number = 0 Then
        objLog.Writeline "Successfully completed the search for a USB drive with the following exit code: " & Err.Number
        Else
        strStatusData = "ERROR - the search for a USB drive failed with the following exit code: " & Err.Number
        objLog.Writeline strStatusData
        strStatusCode = 0
        CreateStatusMIF strStatusData
        End If
        err.clear

        If argPrompt = "1" and strCurrentUser = "1" Then

        If colDrives.count = 1 Then
        For Each objDrive in colDrives
        objRemovableDrive = objDrive.DriveLetter
        objLog.WriteLine "Found USB drive in the system at the following drive letter: " & objDrive.DriveLetter
        Next
        Else If colDrives.count > 1 Then
        strStatusData = "ERROR - More then one USB device was found in your system cannot determine where to save key. Script is quitting..."
        objLog.Writeline strStatusData
        strStatusCode = 0
        CreateStatusMIF strStatusData
        Wscript.Quit -1
        Else If colDrives.count = 0 Then
        objLog.WriteLine "Warning - Did not find USB device to save your startup key. Waiting for user will retry....."
        Wscript.Echo "No removeable USB device was found in your system. To complete the BitLocker configuration please insert a USB removeable drive to save your Startup or Recovery Key."
        WScript.Sleep(10000)
        FindRemovableDrive()
        End If
        End If
        End If
        Else
        If colDrives.count = 1 Then
        For Each objDrive in colDrives
        objRemovableDrive = objDrive.DriveLetter
        Next
        Else
        strStatusData = "ERROR - No USB device available to save key. Script is quitting..."
        objLog.Writeline strStatusData
        strStatusCode = 0
        CreateStatusMIF strStatusData
        WScript.Quit -1
        End If
        End If

        End Function

        '----------------------------------------------------------------------------------------
        'Function 12 - Function used to interogate Group Policy and determine successfully backup of recovery data
        '----------------------------------------------------------------------------------------
        Function EvalGPO

        strComputer = "."
        strPolicy = "0"

        err.Clear
        Set objReg=GetObject("winmgmts:{impersonationLevel=impersonate}!\\" & strComputer & "\root\default:StdRegProv")
        If Not Err.number=0 Then
        strStatusData = "ERROR - Could not connect to WMI StdRegProv" & Err.Description
        objLog.Writeline strStatusData
        strStatusCode = 0
        CreateStatusMIF strStatusData
        Else
        objLog.Writeline "Successfully connected to WMI StdRegProv"
        End If

        err.Clear
        objLog.WriteLine "Checking if Group Policy encryption method is set..."
        strKeyPath = "SOFTWARE\Policies\Microsoft\FVE"
        objReg.EnumValues HKEY_LOCAL_MACHINE, strKeyPath, arrValueNames, arrValueTypes
        If IsEmpty(arrValueNames) = True or IsNull(arrValueNames) = True Then
        strPolicy = "1"
        strStatusData = "No FVE policy registry key found" & Err.Description
        objLog.Writeline strStatusData
        strStatusCode = 0
        CreateStatusMIF strStatusData
        Else
        err.clear
        For R=0 To UBound(arrValueNames)
        If arrValueNames(R) = "EncryptionMethod" Then
        objReg.GetDWORDValue HKEY_LOCAL_MACHINE,strKeyPath,arrValueNames(R),dwValue
        EncryptionMethod = dwValue
        objLog.Writeline "Found EncryptionMethod with value: " & dwValue
        objLog.Writeline "Found EncryptionMethod policy registry key ignoring any /em options on command line"
        argEM = "0"
        End If
        If arrValueNames(R) = "RequireActiveDirectoryBackup" Then
        objReg.GetDWORDValue HKEY_LOCAL_MACHINE,strKeyPath,arrValueNames(R),dwValue
        RequireActiveDirectoryBackup = dwValue
        objLog.Writeline "Found RequireActiveDirectoryBackup with value: " & dwValue
        End if
        If arrValueNames(R) = "ActiveDirectoryBackup" Then
        objReg.GetDWORDValue HKEY_LOCAL_MACHINE,strKeyPath,arrValueNames(R),dwValue
        ActiveDirectoryBackup = dwvalue
        objLog.Writeline "Found ActiveDirectoryBackup with value: " & dwValue
        End if
        Next
        End If

        'Process local policy to see what BDE settings are available

        If ActiveDirectoryBackup = 1 and RequireActiveDirectoryBackup = 1 Then
        objLog.WriteLine "Determined client Group Policy configured to require AD escrow of recovery password"
        BackupMandatory = "1"
        Else If ActiveDirectoryBackup = 1 and RequireActiveDirectoryBackup = 0 Then
        objLog.WriteLine "Warning - Determined client Group Policy is configured to require AD escrow of recovery password but is not mandatory. If AD was not available when BitLocker was enabled recovery data may not be escrowed but BitLocker will be enabled."
        BackupMandatory = "0"
        End If
        End If

        End Function

        '----------------------------------------------------------------------------------------
        'Function 13 - Function used by the EvalGPO function to scan event logs for BitLocker recovery events
        '----------------------------------------------------------------------------------------
        Function getBDEEvents()

        If strPolicy = "1" Then
        Exit Function
        End If

        Set objWMIService = GetObject("winmgmts:{impersonationLevel=impersonate}!\root\cimv2")
        Set colBDEEvents = objWMIService.ExecQuery("Select * from Win32_NTLogEvent Where Logfile = 'System' and EventCode = '514' or EventCode = '513'")
        If colBDEEvents.Count >= 1 Then
        For Each objBDEEvent in colBDEEvents
        If objBDEEvent.EventCode = "514" Then
        objLog.Writeline "---------------------------------------------------------------------------------"
        strStatusCode = "WARNING - Found event log entry showing unsuccessful recovery information backup."
        objLog.Writeline strStatusData
        objLog.WriteLine "Event log ID: " & objBDEEvent.EventCode
        objLog.WriteLine "Event log message: " & objBDEEvent.Message
        objLog.Writeline "---------------------------------------------------------------------------------"
        strStatusCode = 0
        CreateStatusMIF strStatusData
        ElseIf objBDEEvent.EventCode = "513" Then
        objLog.Writeline "---------------------------------------------------------------------------------"
        objLog.Writeline "Found event log entry showing successfull recovery information backup."
        objLog.Writeline "Event log ID: " & objBDEEvent.EventCode
        objLog.Writeline "Event log message: " & objBDEEvent.Message
        objLog.Writeline "---------------------------------------------------------------------------------"
        End If
        Next
        Else
        objLog.WriteLine "Did not find a local event log entry for BitLocker AD backup."
        End If

        End Function

        '----------------------------------------------------------------------------------------
        'Function 14 - Used to create SMS status MIF's
        '----------------------------------------------------------------------------------------
        Function CreateStatusMIF(strStatusData)

        err.clear
        If argSMS = "1" then
        Set MIF=CreateObject("ISMIFCOM.InstallStatusMIF")
        Mif.Create "BitLocker","Microsoft","BitLocker.vbs","1.0","","",strStatusData,strStatusCode

        If Err.number <> 0 Then
        objLog.Writeline "Failed to create the SMS status MIF."
        Else
        objLog.WriteLine "Successfully created the SMS status MIF."
        End If
        End if

        err.clear

        End Function
        '----------------------------------------------------------------------------------------
        'Function 15 - Check for logged on User
        '----------------------------------------------------------------------------------------
        Function CheckUser

        Set colComputer = objSWbemServices.ExecQuery("Select * from Win32_ComputerSystem")
        For Each objComputer in colComputer
        If not objComputer.UserName = "" Then
        objlog.writeline "The following user is logged on: " & objComputer.UserName
        strCurrentUser = "1"
        Else
        objlog.writeline "There is no user currently logged on to this computer"
        strCurrentUser = "0"
        End If
        Next
        End Function
        '-----------------------------------------------------------------------------------------
        'Function 16 - Create a Protect Key With Numerical Password
        '-----------------------------------------------------------------------------------------

        Function CreateRP(objEnVol)
        On Error Resume Next

        Err.clear
        intRC = objEnVol.ProtectKeyWithNumericalPassword("Recovery Password",Empty,vProtID)
        objLog.Writeline "Attempting to create a recovery password..."
        If intRC <> 0 Then
        strStatusData = "WARNING - failed to create recovery password with the following exit code: " & Hex(intRC)
        objLog.Writeline strStatusData
        strStatusCode = 0
        CreateStatusMIF strStatusData

        If Hex(intRC) = "8007054B" and BackupMandatory = "1" Then
        strStatusData = "ERROR - failed to save recovery password to active directory with the following exit code: " & Hex(intRC)
        objlog.writeline "Group Policy is requiring AD backup of the recovery password but AD could not be contacted."
        objLog.Writeline strStatusData
        strStatusCode = 0
        CreateStatusMIF strStatusData

        Err.Clear
        objLog.Writeline "Deleting previously created key protectors..."
        intRC = objEnVol.DeleteKeyProtectors()
        If intRC <> 0 Then
        strStatusData = "ERROR - failed to remove key protectors with the following exit code: " & Hex(intRC) & " Script is quitting..."
        objLog.Writeline strStatusData
        strStatusCode = 0
        CreateStatusMIF strStatusData
        Wscript.Quit -1
        Else
        objlog.writeline "Successfully removed key protectors with the following exit code: " & Hex(intRC) & " Script is quitting..."
        Wscript.Quit -1
        End If
        End If
        Else
        objlog.writeline "Successfully created recovery password with the following exit code: " & Hex(intRC)
        If BackupMandatory = 0 Then
        Wscript.Sleep(5000)
        getBDEEvents
        End If
        Exit Function
        End If
        err.clear

        End Function
        '----------------------------------------------------------------------------------------
        'Function 17 - Request PIN from User
        '----------------------------------------------------------------------------------------
        Function GetPIN

        strPIN=InputBox("Enter your new PIN number. The PIN must consist of a sequence of 4 to 20 digits.")
        If strPIN = "" Then
        strStatusData = "ERROR - User canceled the PIN input operation. Script is quitting..."
        objLog.Writeline strStatusData
        strStatusCode = 0
        CreateStatusMIF strStatusData
        Wscript.Quit -1
        End If

        If IsNumeric(strPIN) Then
        iLen = Len(strPIN)
        If iLen > 3 and iLen < 21 Then
        argValid = "1"
        Else
        i = i + 1

        If i < 3 Then
        Wscript.Echo "The PIN you entered was not 4 to 20 digits please re-enter a valid PIN."
        objLog.writeline "WARNING - User did not enter a PIN that was not 4 to 20 digits."
        GetPIN
        Else
        strStatusData = "ERROR - The PIN was not 4 to 20 digits. You have exceeded your maximum attempts."
        Wscript.Echo "You exceeded the maximum number of attempts(3) to enter a PIN. The process is quitting."
        objLog.Writeline strStatusData
        strStatusCode = 0
        CreateStatusMIF strStatusData
        argValid = "0"
        End If
        End If
        Else
        Wscript.Echo "The PIN you entered contained letters or symbols. The PIN must only contain numbers please re-enter a valid PIN."
        objlog.writeline "WARNING - User did not enter a PIN as a number."
        i = i + 1
        If i < 3 Then
        GetPIN
        Else
        Wscript.Echo "You exceeded the maximum number of attempts(3) to enter a PIN. The process is quitting."
        strStatusData = "ERROR - The PIN was not entered as a number. You have exceeded your maximum attempts."
        objLog.Writeline strStatusData
        strStatusCode = 0
        CreateStatusMIF strStatusData
        argValid = "0"
        End If
        End If

        End Function

        '----------------------------------------------------------------------------------------
        'Function 18 - Determine conversion status
        '----------------------------------------------------------------------------------------
        Function GetConversionStatus(strCS)
        If strCS = 1 Then
        objlog.writeline "The volume has a status of fully encrypted but a clear key is present"
        intRC = objWMIBDE.EnableKeyProtectors()
        If intRC <> 0 Then
        strStatusData = "ERROR - failed to enable key protector with the following exit code: " & Hex(intRC)
        objLog.Writeline strStatusData
        strStatusCode = 0
        CreateStatusMIF strStatusData
        Else
        strStatusData = "Completed method EnableKeyProtectors with an exit code of: " & Hex(intRC)
        objlog.writeline strStatusData
        strStatusBDE = strStatusData
        End If
        Else
        If strCS = 2 Then
        strStatusData = "The volume has a status of encryption in progress"
        objLog.Writeline strStatusData
        strStatusCode = 0
        CreateStatusMIF strStatusData
        Wscript.Quit -1
        Else
        If strCS = 3 Then
        strStatusData = "The volume has a status of decryption in progress"
        objLog.Writeline strStatusData
        strStatusCode = 0
        CreateStatusMIF strStatusData
        Wscript.Quit -1
        Else
        If strCS = 4 Then
        strStatusData = "The volume has a status of encryption paused"
        objLog.Writeline strStatusData
        strStatusCode = 0
        CreateStatusMIF strStatusData
        Wscript.Quit -1
        Else
        If strCS = 5 then
        strStatusData = "The volume has a status of decryption paused"
        objLog.Writeline strStatusData
        strStatusCode = 0
        CreateStatusMIF strStatusData
        Wscript.Quit -1
        End If
        End If
        End if
        End if
        End if

        End Function


        '----------------------------------------------------------------------------------------
        'Function 19 - Check protect errors for any know problems
        '----------------------------------------------------------------------------------------
        Function CheckError(intRC)

        If Hex(initRC) = "80310030" Then
        strStatusData = "ERROR - There is a boot CD/DVD or USB device in the system please remove and restart script. Script is quitting..."
        objLog.Writeline strStatusData
        strStatusCode = 0
        CreateStatusMIF strStatusData
        Wscript.Quit -1
        End If

        End Function

        '----------------------------------------------------------------------------------------
        'Function 20 - Shows help for the script
        '----------------------------------------------------------------------------------------
        Function ShowHelp
        On Error Resume Next
        WScript.echo "************************************************************************************************************************************" & vbCr & _
        "Example: EnableBitLocker.vbs /on:tpm /l:c:\bitlocker.log," & vbCr & vbCr & _
        "/on:<tpm,tp,tsk,usb>" & vbTab & "used to specify options for turning on BitLocker (tpm,tp,tsk) REQUIRED" & vbCr & _
        "/l:<location>" & vbTab & vbTab & "specify to create a log file and it's location REQUIRED" & vbCr & _
        "/rk:<location>" & vbTab & vbTab & "create a recovery key and store in a particular location OPTIONAL" & vbCr & _
        "/em:<128d,256d,128,256>" & vbTab & "used to specify encryption algorithm if left out aes128d is used (aes128d, aes256d, aes128, aes256) OPTIONAL" & vbCr & _
        "/promptuser" & vbTab & vbTab & "causes script to prompt user for TPM PIN or to insert USB drive OPTIONAL" & vbCr & _
        "/sms" & vbTab & vbTab & vbTab & "creates an SMS status MIF for software distribution OPTIONAL" & vbCr & _
        "/ro:" & chr(34) & "<oldownerpassword>" & chr(34) & " " & vbTab & "reset the TPM ownership using the existing owner password (password must be placed between quotes) OPTIONAL" & vbCr & vbCr & _
        "************************************************************************************************************************************" & vbCr & _
        WScript.quit
        End Function

        Also in our environment we have gotten away from any local admins on the machines. I am currently local admin on my machine for testing purpose while setting up all of our software packages. Adding a network admin as local may be a posibility but is not currently how our systems are setup, So our network admins are not setup as local on the clients machines. We are using a Network admin account to install post install tasks since all of our software packages are on located on a share on our network.

        Thank you again for all of your work working thru this issue - tmcvay828 9 years ago
      • Is the account you are using for this a member of the local admins group on the machines? "We are using a Network admin account to install post install tasks since all of our software packages are on located on a share on our network" - SMal.tmcc 9 years ago
      • SMal..
        No, the Network admin creds that I am using are not part of the local admin group on the client machines..
        We currently do not have any "local admins" on the client machines at all..
        I do setup a local admin during the unattend.vbs for the build but this user is not part of the network admin group so if I use this account the pos install packages do not install.. My thought is to add the local admin created during the unattend be added to the network admin group also to see if this corrects my issue.. - tmcvay828 9 years ago
      • you need to make the user you are using a member of the local admin group. You can do this via GPO or as a post task. or like you said, the local user you are using give rights to the network share. - SMal.tmcc 9 years ago
      • Thank you.. I will give this a shot and let you know how it goes - tmcvay828 9 years ago
      • Finally having time to sit and look over everything I found that during the script I was creating a log file to a directory that did not exist. This was causing the script to fail with no information and look like it completed. Once the script was written to create the directory before the script was run it would allow the script to function correctly.. So now seems that permissions had nothing to do with the script failing after all.. Thank you for all of your help!! - tmcvay828 9 years ago
 
This website uses cookies. By continuing to use this site and/or clicking the "Accept" button you are providing consent Quest Software and its affiliates do NOT sell the Personal Data you provide to us either when you register on our websites or when you do business with us. For more information about our Privacy Policy and our data protection efforts, please visit GDPR-HQ